S & S SUPER E & G FOR TWINCAM  

 

WITH FLO-TEC MANIFOLD

Kit contains: Breather Bracket polished stainless steel banjo bolts, S&S adapter rings, Breather Bracket spacers, O-Rings, mounting hardware, FLO-TEC manifold and Nitrile rubber gasket.

 

close this window

 

DOWNLOAD INSTALLATION
INSTRUCTION SHEET

MAC - PC
 

S&S for Twin Cam is the most difficult for us at the moment because the Twin Cam has wider fins on the cylinders than the Evo. It's necessary to either shave a few milimeters off three of the fins between the cylinders, to get the S&S carb deeper into the motor, or use one of our spacer kits.

We prefer the shaved fins option because the spacer adds an extra 22-25mm to the out-hang of the assembly, and this can be an issue with leg clearance.

There are 2 ways to go with S&S for Twin Cam:

(1) The S&S MANIFOLD, with FLO-TEC Threaded Spacer Option:

SEE THE (S&S SUPER E & G FOR EVO - WITH S&S MANIFOLD and FLO-TEC SPACERS) OR (S&S SUPER E & G FOR TWIN CAM - WITH S&S MANIFOLD and FLO-TEC SPACERS) PAGES

Using the S&S cast manifold is possible, but because of the length of the manifold entrance, the FLO-TEC Breather Bracket needs to be spaced 22-25mm from the heads. This kit contains the spacers, grooved to accept O-Rings. It adds 22-25mm to the out-hang of the FLO-TEC bracket, and intake components, which may cause leg clearance problems on some models. SEE THE (S&S SUPER E & G FOR EVO - WITH S&S MANIFOLD and FLO-TEC SPACERS) OR (S&S SUPER E & G FOR TWIN CAM - WITH S&S MANIFOLD and FLO-TEC SPACERS) PAGES

(2) THIS PAGE -The Complete FLO-TEC Option:

Our preferred fit for S&S carbs, though because the fins on the Twin Cam motor are wider than Evos it's necessary to shave 3 of the lower fins to fit the carb in behind the Breather Bracket, on this manifold. We supply you with a template drawing. As with Evos, our short entrance manifold puts the FLO-TEC 25mm deeper in the motor, enabling it to fit neatly in behind the breather bracket, with no extra spacers between the Bracket and the heads.

This kit also contains a specially cast rubber gasket, which is profiled on the front edge to match the carb casting, and on the rear edge to match the manifold. The result is a clean and properly matched union with no ugly steps or overlaps. Manifolds available in all lengths and finishes. See the manifolds section for all the options. Rubber gasket available in Grey or Black.

A manual choke knob kit is needed to replace the choke lever that would usually be on the back of the S&S filter backing plate. You can obtain this from S&S, or we can supply you with our custom kit.

We do our own shorter-entrance manifold, based on the short Mikuni manifold, and a specially cast Nitrile rubber gasket that mates the carb to the manifold. The manifolds are available for stock (1.815"OD/1.625 ID) or S&S (1.880" OD/1.780" ID) diameter intake ports, and with VOES for Evo, sensor boss for Twin Cam, or plain.

Using one of our manifolds allows the breather bracket to mount directly to the heads. Requires shaving a few milimeters off three of the fins between the cylinders. We supply a template drawing.


Using one of our manifolds allows the breather bracket to mount directly to the heads, without the FLO-TEC spacer, but three fins need shaving to fit the carb body deeper in the motor.
 

WHAT TO ORDER

You'll need the Complete FLO-TEC mounting bracket and manifold kit (correct width for the size of your motor), then either the then horn and/or the air filter assembly of your choice.

S&S SUPER E SHORTY - WITH FLO-TEC MANIFOLD (SUPER G FITMENTS ARE LISTED BELOW)
         

PART NO.

MOTOR TYPE

FINISH

BREATHER WIDTH

MANIFOLD

219412P

TWIN CAM (3/8"UNC BREATHER HOLE)

POLISHED

STOCK FLO-TEC

FLO-TEC

219413P

TWIN CAM (3/8"UNC BREATHER HOLE)

POLISHED

plus 10.5mm

FLO-TEC

219414P

TWIN CAM (3/8"UNC BREATHER HOLE)

POLISHED

plus 5.0mm

FLO-TEC

219415P

TWIN CAM (3/8"UNC BREATHER HOLE)

POLISHED

plus 2.5mm

FLO-TEC

219416P

TWIN CAM (3/8"UNC BREATHER HOLE)

POLISHED

minus 2.5mm

FLO-TEC

219417P

TWIN CAM (3/8"UNC BREATHER HOLE)

POLISHED

minus 5.0mm

FLO-TEC
         

219412A

TWIN CAM (3/8"UNC BREATHER HOLE)

CLEAR ANODISED

STOCK FLO-TEC

FLO-TEC

219413A

TWIN CAM (3/8"UNC BREATHER HOLE)

CLEAR ANODISED

plus 10.5mm

FLO-TEC

219414A

TWIN CAM (3/8"UNC BREATHER HOLE)

CLEAR ANODISED

plus 5.0mm

FLO-TEC

219415A

TWIN CAM (3/8"UNC BREATHER HOLE)

CLEAR ANODISED

plus 2.5mm

FLO-TEC

219416A

TWIN CAM (3/8"UNC BREATHER HOLE)

CLEAR ANODISED

minus 2.5mm

FLO-TEC

219417A

TWIN CAM (3/8"UNC BREATHER HOLE)

CLEAR ANODISED

minus 5.0mm

FLO-TEC
         

219412B

TWIN CAM (3/8"UNC BREATHER HOLE)

BLACK ANODISED

STOCK FLO-TEC

FLO-TEC

219413B

TWIN CAM (3/8"UNC BREATHER HOLE)

BLACK ANODISED

plus 10.5mm

FLO-TEC

219414B

TWIN CAM (3/8"UNC BREATHER HOLE)

BLACK ANODISED

plus 5.0mm

FLO-TEC

219415B

TWIN CAM (3/8"UNC BREATHER HOLE)

BLACK ANODISED

plus 2.5mm

FLO-TEC

219416B

TWIN CAM (3/8"UNC BREATHER HOLE)

BLACK ANODISED

minus 2.5mm

FLO-TEC

219417B

TWIN CAM (3/8"UNC BREATHER HOLE)

BLACK ANODISED

minus 5.0mm

FLO-TEC

S&S SUPER G SHORTY - WITH FLO-TEC MANIFOLD
         

PART NO.

MOTOR TYPE

FINISH

BREATHER WIDTH

MANIFOLD

219446P

TWIN CAM (3/8"UNC BREATHER HOLE)

POLISHED

STOCK FLO-TEC

FLO-TEC

219447P

TWIN CAM (3/8"UNC BREATHER HOLE)

POLISHED

plus 10.5mm

FLO-TEC

219448P

TWIN CAM (3/8"UNC BREATHER HOLE)

POLISHED

plus 5.0mm

FLO-TEC

219449P

TWIN CAM (3/8"UNC BREATHER HOLE)

POLISHED

plus 2.5mm

FLO-TEC

219450P

TWIN CAM (3/8"UNC BREATHER HOLE)

POLISHED

minus 2.5mm

FLO-TEC

219451P

TWIN CAM (3/8"UNC BREATHER HOLE)

POLISHED

minus 5.0mm

FLO-TEC
         

219446A

TWIN CAM (3/8"UNC BREATHER HOLE)

CLEAR ANODISED

STOCK FLO-TEC

FLO-TEC

219447A

TWIN CAM (3/8"UNC BREATHER HOLE)

CLEAR ANODISED

plus 10.5mm

FLO-TEC

219448A

TWIN CAM (3/8"UNC BREATHER HOLE)

CLEAR ANODISED

plus 5.0mm

FLO-TEC

219449A

TWIN CAM (3/8"UNC BREATHER HOLE)

CLEAR ANODISED

plus 2.5mm

FLO-TEC

219450A

TWIN CAM (3/8"UNC BREATHER HOLE)

CLEAR ANODISED

minus 2.5mm

FLO-TEC

219451A

TWIN CAM (3/8"UNC BREATHER HOLE)

CLEAR ANODISED

minus 5.0mm

FLO-TEC
         

219446B

TWIN CAM (3/8"UNC BREATHER HOLE)

BLACK ANODISED

STOCK FLO-TEC

FLO-TEC

219447B

TWIN CAM (3/8"UNC BREATHER HOLE)

BLACK ANODISED

plus 10.5mm

FLO-TEC

219448B

TWIN CAM (3/8"UNC BREATHER HOLE)

BLACK ANODISED

plus 5.0mm

FLO-TEC

219449B

TWIN CAM (3/8"UNC BREATHER HOLE)

BLACK ANODISED

plus 2.5mm

FLO-TEC

219450B

TWIN CAM (3/8"UNC BREATHER HOLE)

BLACK ANODISED

minus 2.5mm

FLO-TEC

219451B

TWIN CAM (3/8"UNC BREATHER HOLE)

BLACK ANODISED

minus 5.0mm

FLO-TEC